Annotated Bib Gender Roles

Gender Roles in the Workplace: Annotated Bibliography Karissa Roveda Oakland University Rochester, MI Adler, M. A. (1994). Male-Female power differences at work: A comparison of supervisor and policymakers. Sociological Inquiry, 64(1), 37-55. This article spoke of the positions of power between men and women, and how policymakers and supervisors distribute that power to men and women. In the work place, when considering for advancement, employers have undefined criteria such as personality characteristics and potential managerial qualities.These standards become the cause of inequality in authority and power at work place. Jobs that are available for women have low wages and also less authority. Similar research studies have shown similar points, in that inequality is found at the workplace because of such gender based characteristics. Even though women were shown to be more educated, they do not follow the same status. The researcher in this study used methodology to find these ineq ualities at the work place. The study consisted of four data points to test and used 531 women and 619 men for this data.The author collected data for power in wage labor, employment, sample characteristics and occupation by education. The results showed that men achieve higher positions and also showed they have a higher chance at a supervisory level and more authority than women. In the workplace, gender is a major part of determining positions of power. Also, it shows that education is more important to get supervisor positions, which is less effective for women. This study demonstrates the inequality between men and women that makes men more prone to positions of power than women.The data and research clearly showed that women have greatly less access to positions of power and authority at work place than men, and that gender is the key factor in determining those positions. Policymakers and supervisors may indeed make regulations promoting equality but gender bias is still obvi ously exhibited. Carbonell, J. L. , & Castro, Y. (2008). The impact of a leader model on high dominant women’s self-selection for leadership. Sex Roles ,58,776-783. This study had women observe a leader model of either gender model a task they would have to complete. The study looked at effects of ender role model in the decision of high dominant women to be leaders, given a masculine task to complete with a male co-worker. The hypothesis states that women would become leaders at a higher rate when a woman model is given rather than a male. The research took a total of 190 students: 95 women and 95 men. Each individual was given the California Psychological Inventory, measuring: impression, communication, and dominance. This study looked at dominance in particular. Only 15 pairs were exposed to women models. The study observed 2 groups to support or reject their hypothesis.Focused groups were made of high dominant woman paired with a low dominant man with a female model, and high dominant woman paired with a low dominant man with a male model. A chi square analysis showed a correlation between leader model and leader development, â€Å"The results are that 60% of women took the leader role when given a woman model compared to 20% in male model† (Castro, 2008). The study concluded in the presence of a female model, high dominant individual would be the leader. The gender of the leader model did not affect leadership for males. I believe this study shows importance of woman leader models in professional fields.The lack of exposure of woman leaders for women reduces the chances that they will take on leadership roles. Katz, D. (1987). Sex discrimination in hiring: The influence of organizational climate and need for approval on decision making behavior. Psychology of Women Quarterly, 11(1), 11-20. Previous studies have caused the idea that equally skilled men and women are assessed unequally when applying for jobs. The present study observes the inf luence from different organizational workplaces or â€Å"the quality of an organization’s internal environment† (Katz, 1987), and society’s need for approval on the notion of biased employees decisions.The study sought out three main hypotheses, if an unfair organizational environment would influence people to hire a male applicant over an identical female applicant. Second, that in a workplace a male applicant would be ranked as a better fit and more likely to stay with the company longer than a female applicant. And third, that those subjects with a high need of approval would match more to the demands of job on the hire and salary assessments than lower approval motivation applicants. The study included 161 male undergrads enrolled in a business class.They were given a booklet which contained experimental materials necessary in controlling organizational workplace. They were also given either a female or male completed application and asked for their judgment s on an applicant’s suitability for the position. Results from the experiment showed that as initially expected, males were favored over females in the unfair environment. The results also showed that males were chosen as fitting significantly better than females, and that men were also offered higher salaries in the same conditions.In my opinion, the implications of this study can establish that the workplace can deeply influence the decisions of hiring workers and lead to gender bias. McTavish, D. , & Miller, K. (2009). Gender balance in leadership? Reform and modernization in the UK further education sector. Educational Management Administration & Leadership, 37(3), 350-365. The research question that this article attempted to answer was â€Å"Why are few women advancing into leadership positions despite a large number of women being employed into the further education sector? † (McTavish & Miller, 2009).The further education sector employs a high proportion of wome n yet relatively few women progress into leadership positions. The article seeks to provide explanations for this gender imbalance and argues that despite change and modernization initiatives, the further education sector remains gendered in many aspects of leadership, governance and executive practices. The only major difference between male and female academics was that female academics were twice as given to apply for promotion if supported by their line manager, and male academics were twice as likely to apply if there was an opportunity to influence college power.Also female academics were twice as likely to apply if they were obtained feedback through their staff review. There are many conclusions that were drawn from this study. Reform and structural change have definitely led to a larger number of possibilities for women. Changes in organizational policy have led to a friendlier environment for females. Women have to adjust to masculine managerial styles, such as competitive ness. In addition, even though it appears that the reforms are creating gender balance, in reality; women are still going to their stereotypical roles such as teaching and lecturing.Meyerson, Debra E. , and Joyce K. Fletcher. â€Å"A Modest Manifesto for Shattering the Glass Ceiling. † Harvard Business Review (2000): 127-36. â€Å"Gender discrimination is now so deeply embedded in organizational life as to be virtually indiscernible. Even the women who feel its impact are often hard-pressed to know what hit them† (Meyerson & Fletcher, 127). The authors believe that the glass ceiling will be shattered â€Å"only through a strategy that uses small wins-incremental changes aimed at biases so entrenched in the system that they're not even noticed until they're gone† (Meyerson & Fletcher,128).The small wins approach to change was developed by Karl Weick. The authors emphasize that real and lasting change can be made by small changes, and that these small changes are not threatening to any stakeholders. For example, one firm discovered it could recruit women more effectively simply by increasing the length of the interview time from 30 minutes to 45 minutes, which gave female candidates just a little bit more time to â€Å"bond† with their middle-aged male interviewers. Another firm reversed its high turnover rate for female middle managers by bringing more discipline to meetings, ensuring that meetings started and ended on time.This would be a change that freed all employees from the need to be available 15 hours per day. I personally think both strategies are very effective because at least these firms are putting in the effort to make a difference through the gender roles fairness in the workplace. Roos, P. A. (1981). Sex stratification in the workplace: Male-Female differences in economic returns to occupation. Social Science Research, 10(3), 195-224. The study causes the idea that there is a large earning gap between men and women.Ge nder differences in earning are important because it focuses on the gender-based inequalities of power at the workplace. The author of the study used a literature review to explain the gender gap in earning, and it showed that sex segregated characteristics still remain at the occupational level. It shows that women work at low paying jobs and they are less likely to use authority in those jobs. The main reason why there are gender differences in earnings is the belief of human capital theory, and it has a huge concern with the supply side of the market.The researcher used a non-institutionalized English speaking population to explain the data for gender influenced gap in earning. The sample included 959 men and 670 women. The results showed that women are paid low wages, and are in positions of low responsibility. Even when a women reaches a higher level job, their earning is much lower than that of men. The results also show that women’s low income is mainly because of thei r job characteristics, in that men and women are distributed differently across jobs.Men earn more than women, mainly because women are not considered employers. The study demonstrated that the characteristics of the workers create inequality at the workplace; this is also a reason for why there is a large gap in earning between genders. Human capital theory discourages women from working and it presents women as low rent employees. They have less understanding of the mean of production. The characteristics of this research show improvement in the earnings of men and women. Yuping Zhang and Emily Hannum and Meiyan Wang. Gender-Based Employment and Income Differences in Urban China: Considering the Contributions of Marriage and Parenthood. † Social Forces 86. 4 (2008): 156-159. Web. 2 April 2010. This article is based on the income differences and job opportunities of workers in urban China between men and women and why these differences exist. These authors argue that married women and parents receive the biggest disadvantage amongst female workers in China due to their lack of capital regarding education, energy and financially.These particular women are not able to make as many social connections as men do due to their role in the household and so they are at a great disadvantage. In China’s market it is essential to have these kinds of social connections. It is a capitalistic society where everyone is out for his or herself and so people must use other people to get what they want. If these connections are not present then these urban female workers will not be able to make nearly as much progress and therefore will be much less successful.It is these expectations that cheapen the women and set them at a great disadvantage if they ever plan on having a family and household to upkeep. This lack of opportunity in the article is summarized as a disadvantage of ‘time use’ due to being a wife and having children in comparison to those w ho do not. However, if a woman were to decide that she didn’t want a family and wanted to primarily focus on her work this would be frowned upon in society, due to how valued the dynamic of family is in China.

Main functions of GO4IT Sports Essay

* The company has a warehouse which supplies goods to shops as well as to sports teams by mail order * The company sells a wide range of sports goods in it shops this includes clothing, footwear and equipment for sports. * The shops also sell exercise equipment; however these large items are not kept in stock but are ordered from the supplier as required. * The company supplies match strips, to order, in team colours for different sports * The company supplies other team merchandise with team logo; these are supplied through a mail order service. * Sell sports trophies which can be engraved if required. * The company also supplies sports clothing in bulk to schools Different types of customers for GO4IT Sports The company’s customers include: * Schools * Sports teams for all sports such as football, rugby, tennis, athletics and golf * General customers * The shops which are supplied by the company’s warehouse Describe the functions of each section within the shops and Head Office, paying particular attention to Administration in shops and Human Resources in Head Office Functions of each section within the shops Administration * Each shop has a Branch Manager who has overall responsibility for the running of the shop. * The assistant manager and head of administration section report directly the branch manager. * The staff keeps account of the money taken through the EPOS terminals by comparing money received with EPOS records. * The administration staff produce and send correspondence from the shop as well as receiving correspondence. * Organise for a trophy to be engraved by contacting the local engraver. * Emailing weekly orders for goods to the warehouse * Producing confirmation purchase orders for goods and services * Checking invoices against goods received and work done and passing these to Head Office for payment Clothing sales * The clothing sales section has a clothing sales manager who the clothing sales staff and footwear sales staff report to. * Clothing Sales staff assist customers in choosing appropriate clothing and provide advice for those who wish to purchase clothing * The footwear sales staffs assist customers and provide advice for those who wish to purchase footwear. Equipment sales * The Equipment sales section has an Equipment sales manager. The general sales staff and specialist sales staff report to the Equipment sales manager. * The General sales staff operate the EPOS terminals, they scan the barcodes of every items during purchase and handing of receipts. * The Specialist sales staffs provide assistance and specialist advice and information for customers purchasing more advanced equipment. Functions within the Head Office * The Managing Director of GO4IT sports is responsible for all aspects of the day to day running of the business. The two directors which are: sales marketing director and the finance and administration director report to the managing director Sales and Marketing * The sales and marketing director is responsible for the mail order operation as well as advertising and promoting the business * A buying manager is responsible for locating the goods to be sold and negotiating contracts for their supply. * The buying manager ensures the right volume and type of goods are supplied at the right time to maximise profit. Finance and Administration * The Finance and Administration director is responsible for all other functions within the Head Office. This includes administration, Human Resources(HR) and finance * The Administration assistant, HR executive, chief accountant and ICT support executive report to the Finance and Administration director Finance * Keep records of all financial transactions on the head office server, including the income from sales for each shop and mail order, payments for goods purchased, payments for engraving contractors and staff wages. * Records are used to produce monthly and annual accounts for shareholders and Inland Revenue. * Generate VAT (value added tax) returns once a quarter for customs and excise. * Arrange for the amount due to be paid. Human Resource (HR) The functions of the HR Department are; * Staff recruitment and training * Place advertisements for staff * Send out and receive application forms * Organise interviews and provide contracts for successful applicants * Keeping standard personnel records on a database along with records of training courses attended by members of staff and any qualifications they obtain. * Determine what further training each staff member requires and how best to provide it * Book the member of staff on an external training course/ if many members require training organise for a trainer to deliver the course ‘in house’. Task1 Identify different types of supplier to the shops and warehouse and describe relationships between these suppliers and the departments/individuals within the company Warehouse Supplier What is supplied Who orders it How and when it is ordered Wholesaler Clothing and footwear Warehouse manager Order is made by fax once a month but can place special order by telephone if stocks of a particular item falls faster then expected Specialist manufacturers Sports equipment Buying Manager The buying manager negotiates contracts at the beginning of each season either by telephone or visit, for the supply of a certain quantity. Shops Supplier What is supplied Who orders it How and when it is ordered Local Engraver (external Contractor) Engraved Trophy Administration Assistant Administration Assistant telephones local engraver. The engraver collects the trophy from the shop with a confirmation purchase order detailing work the required. Warehouse Clothing and footwear Administration staff Branch manager hands an annotated stock list to Administration staff who e-mails warehouse Task 2 An analysis of the processes for recording sales in a shop and for mail order sales in Head Office. Shop Information Required * Product bar code or numerical code if bar code unreadable * Quantity bought * If sale is to be paid by credit card * If paying by cash the Amount to be tendered From where this is obtained and how it is captured * product code by barcode scanner * numerical code keyed in using a keypad * quantity keyed in by till operator * credit card yes/no keyed in The processing and calculations required * look up item in computer * display item name and price on screen * multiply price by quantity * if on sale, reduce total price by 50% * display total on screen * if credit card = yes, generate credit card receipt for signature The form and content of any output * on-screen / display message * paper till receipt * paper credit card receipt * Contains prices. items, sales items highlighted with words â€Å"ON SALE†, store address, time of sale, till operator name Mail Order in Head Office Information Required * Team details e.g. team name, name and address of contact person, the sport, the colour(s) and design of shirt/vest, position of logo e.g. VTL(vest top left), picture of team logo and team number * Product colour * Product quantity required * Product code * Colour code/ X is entered If a non standard colour * Size and number of colours in logo * Amount of deposit paid From where this is obtained and how it is captured * Team details from completed order form from a mail order brochure entered onto data screen on computer using input devices such as keyboard and mouse * Product colour from completed order form from a mail order brochure entered onto data screen on computer using input devices such as keyboard and mouse * Product quantity required from completed order form from a mail order brochure entered onto data screen on computer using input devices such as keyboard and mouse * Product code from completed order form from a mail order brochure entered onto data screen on computer using input devices such as keyboard and mouse * Colour code/ X is entered If a non standard colour from completed order form from a mail order brochure entered onto data screen on computer using input devices such as keyboard and mouse * Size and number of colours in logo from completed order form from a mail order brochure entered onto data screen on computer using input devices such as keyboard and mouse * Amount of deposit paid from completed order form from a mail order brochure entered onto data screen on computer using input devices such as keyboard and mouse * Team logo captured using a scanner and stand alone computer The processing and calculations required * look up item in computer * display item name and price on screen * Calculate price of embroidery by multiplying number of logos by price * multiply price by quantity * Calculate sub total if less than à ¯Ã‚ ¿Ã‚ ½100, à ¯Ã‚ ¿Ã‚ ½5 is added for postage and packaging * Calculate and add VAT to give total price The form and content of any output * on-screen / display message * Invoice * Contains prices. items, store address, store phone and fax number, date of sale, invoice number, team contact person details, sub total, VAT, total, Less deposit, total due. Task 3 Outlining the current ICT systems used by GO4IT Sports, in particular, Finance within Head Office and Administration within a Shop Administration within a shop * Each shop has a number of Electronic Point of Sales (EPOS) terminals with barcode readers and card readers. * Telephone connection to banking system * Small Local Area Network (LAN) of three computers * Laser Printer * Branch managers computer acts as a server * Dial up modem Software used includes * Word processing * Spreadsheet applications Finance within Head Office * Number of workstations * Local are network (LAN) * Single Server * Fast laser printer * Slower laser printer * Bar code reader * ISND line Software used includes * Word processing * Spreadsheet applications * Database management software * Stock control software Task 3 Analysing the purpose and operation of the main ICT systems used for sales in each shop and the ICT systems using within the warehouse Shops * Each shop has an EPOS terminal with barcode readers and card readers. Stock data is held on dedicated server connected to the EPOS terminals. * There is also a telephone connection to the banking system for authorisation of the card payments. * The barcode reader is used to scan the barcode of each item and the product code it contains is used to look the product description and price from stock database * When items are scanned total price is calculated. This includes the VAT, the system calculates the net value of the items, and all of this is printed on the receipt. * If customer pays by cash, member of staff enters the amount tendered; the EPOS terminal calculates the change due. This is printed on receipt and given to customer * If customer wishes to pay by credit or debit card the member of staff swipes the card through the card reader. The card details are checked by the banking system and if the transaction is approved an authorisation code is transmitted to the EPOS terminal. * The authorisation Code and card details and amount debited are printed on receipt which is handed to customer to sign with card and items purchased. Warehouse * Stand alone computer * Scanner * Computer controlled embroidery machine * Workstation * Laser printer * Stock control software has separate screens for incoming and outgoing goods. * All goods have a product code which is contained in a barcode. When goods arrive in the warehouse the barcode of each product is read and the quantity entered via the keyboard. * This data is used to update stock database. * For every order picked up the staff use the barcode reader to input the product code and the keyboard to enter the quantity removed from stock. These items are deducted from stock database. Task 3 Recommending and explaining improvements/ extensions to shop systems Methods for improving stock control and the re-ordering of stock, as well as integration of systems within GO4IT sports. * A dedicated server could be used instead of the branch manager’s computer acting as a server, if the branch manager’s computer crashes then that would leave the other computers stranded without a printer and no access to the internet. * ISDN connection would improve communication giving workers a faster connection to send e-mails internally. Dial up connections are not as reliable and are slower so information being sent will be limited due to connection speed of dial up. * There should be a centralised database put into place. This is where all the company’s data is held in one place and the computers in the company are networked. This central database can be used by anyone within the company provided they have been given access through a password. This will be a very resourceful way of storing company data, as it will prevent the problem of data duplication. * Sales based ordering where automatic re-ordering takes place of goods from the warehouse using the sales information from the checkouts. * To increase the efficiency of communication between the supplier and GO4IT sports I would recommend the introduction of EDI (electronic data interchange); the system is similar to email and allows users to exchange invoices, delivery notes, orders and receipts over the telephone network. Security * Log in pages requiring a specific unique user name requiring a private password to track who logs on and off to restrict users Possible problems for suggested improvements * One of the problems that may arise is the finance to cover the costs for the installation of the systems in place. * Also addition of new feature will mean that staff are not familiar with it and training for staff will be required. Benefits of using new technology EDI Advantages * It is much faster, as work does not have to be printed, it is on the screen * The EDI system is easy to use and work can be sent off very easily * Information can be sent to other companies, in less then a few minutes instead of days. * The company can be linked up with their bank, suppliers and customers. * Will minimize the amount of paperwork and business can be transacted much faster and more efficiently then is possible through the normal post. Disadvantages * For EDI, computers are relied on, therefore if the systems go down; it will have a huge of affect on the company. * It is very costly for the installation of EDI * The organization has to research into which system would be best for the company Ecommerce Advantages * Majority of the work of GO4IT sports can be done just through the internet, making it much easier. * This would means a lot less people will have to be employed this will result in huge savings for the company as most transaction will be electronic. * Currently GO4IT sports uses a lot of time to get into contact with suppliers by using the telephone, which can be tedious due to the telephone being engaged; by using e-commerce orders could be automatically electronically sent straight to the suppliers. * Team contacts currently have to post the payment to the company, which is very time consuming and not very secure and with using ecommerce an electronic funds transfer could be made. * Promotion of the company can be improved as it is all online presentation of online advertising can be enhanced. * This will also enable the company to advertise their products online and also allow customers to purchase the products directly from the site using their debit/credit card. They can place the desired items in the virtual shopping trolley. The company can be fully based on the internet, making it easier for the company and also for customers. Disadvantages * A close relationship between the retailer and supplier is required in order for the system to work * Returning products online will prove to be difficult. The customer may be put off when these areas are taken into account. As the customer will question how to send the goods back to their source? Who pays for the return postage? Will the refund be paid? Will I be left with nothing? How long will it take? Compared to offline experience of returning goods to a shop and it is frustrating for the customer. * Privacy, security, payment, identity, contract. Many issues arise – privacy of information, security of that information and payment details, whether or not payment details (eg credit card details) will be misused, identity theft, contract, and, whether we have one or not, what laws and legal jurisdiction apply. MIS(management information systems) For the Buying Manager I would recommend the following improvements: * MIS could produce an analysis of patterns of sales in the company * MIS would be able to identify peak production needs * What if type questions could be applied to different patterns of sales The features of the MIS system that could be used by the branch manager are: * Production costs can be based on raw material costs * MIS could be used to carry out analysis automatically * Results could be displayed in graphs which are easy to understand * Monthly graphs could be produced of price comparison with competitor’s goods or services resulting from regular market research. * Planning, directing, controlling and forecasting decisions. Both managers would benefit from the following points of the MIS system: * Warnings could be set if production costs exceed budget. * Warnings could be set if stocks fall below fixed level.

Choice and Real Life Product Essay

Abstract: In the lab that was conducted, students were supposed to examine the tendencies of fruit flies, specifically Drosophila’s, to move toward or away from important stimuli that aide in their survival, also known as taxis. Another objective for this lab was to identify the patterns and relationships between environmental factors and a living organism. Students are supposed to use two bottles to allow the flies to choose which side they want to go to, depending on what substances they are attracted to more. Fruit flies are not attracted to fruits; rather they are attracted to the rotting fruit. Problem: In this lab, students are studying the behavior of animals, ethology, and the factors that contribute to the way they behave. Do certain environmental factors behave as a stimulus to animals? Hypothesis: If the fruit flies were given choices on which substance they are most attracted to, they there wouldn’t be any preference to any over the other. Materials & Procedures: Material: In this experiment, the we used: tape, 2 water bottles, scissors, 6 different cotton balls, 1 chamber, about 20 fruit flies, water, lime water, banana, vanilla extract, and ammonia. Procedure: Cut the bottom ends off of two water bottles, and tape them together. I labeled each cap with letter â€Å"A† and â€Å"B.† I then inserted the fruit flies in through one end. For each new substance, we dropped a few drops of it onto the cotton balls. We observed the fruit flies for about 5 minutes, undisturbed, and then counted the flies at each end. We repeated these stepped for each new substance being exposed to the flies. Data/Results Table 1. Fruit Fly Choices |Trail 1 |Trail 2 |Trail 3 |Trail 4 | Limewater |Water |Ammonia |Limewater |Vanilla |Banana |Limewater |Banana | |13 |1 |0 |3 |7 |13 |5 |20 | | Questions: 1. Did the flies demonstrate a chemotaxis in relation to any of the substances you chose? Be specific. Chemotaxis is a movement in response to the presence of a chemical stimulus. The flies demonstrated a chemotaxis to the vanilla, lime water, and banana. For each trail, the flies either went one way or the other in response to the substance they preferred. 2. Which substances had the greatest positive and negative chemotactic response? Through the trailing, it is evident that some of the substances had positive and negative responses. In this lab that was conducted, the vanilla extract and banana had the strongest positive responses, while ammonia and water had the most negative responses. Ammonia killed all of the fruit flies that were inside the choice chambers. 3. Describe some possible reason for their preferences? Some possible reasons for their preferences are that they mostly are, however, attracted to fruit. Most of them like the smell of the fruit, and in this case the banana because it rots quickly. 4. What other factors might affect whether or not the fruit flies moved from one part of your choice chamber to another? 5. How can you apply this lab to a real world setting? How might fruit fly preference translate to a real life product? This lab can be  applied to the real world setting not only shown through fruit flies, but also with humans. The fruit fly preference can translate to a real life product by, for say in a restaurant they wouldn’t stay where the ketchups or what have it, but it would be near the garbage area devouring over the rotting food. Conclusion: From this experiment, the behaviors of fruit flies were observed and investigated. Through the sampling of different substance in the choice chambers, it was found that the flies found the banana more desirable than the others and moved towards that side more quickly. This proved the hypothesis that was stated was incorrect. Although, we did make an error; in the trail with ammonia, we added a prodigious amount, which therefore led to the mass killing of the fruit flies causing us to use new ones for the other substances.

Discuss the motives underlining M&A and compare the outcomes of the Essay

Discuss the motives underlining M&A and compare the outcomes of the different methodologies used to analyse M&A - Essay Example There are two types of acquisitions; â€Å"private and â€Å"public†. This depends on whether the company acquiring is or is not listed on a public stock market. The difference between Merger and Acquisition is that Merger deals with two companies joining to become one while Acquisition has one company, which is doing the buying (Sherman and Hart, 20016:11). The work that follows discusses the motives underlying M&A, and compares the outcomes of the different methodologies used to analyze M&A. All companies that engage in any business are under one rule: grow or die. Those companies that plan to grow take away market share from their competitors look for the creation of economic profits and provide returns to shareholders (Sherman and Hart, 2006: 1). Those that lack plans on growth are stagnant, do not plan any growth strategies, they end up losing customers and market share and lose shareholder value. Mergers and Acquisitions contribute a lot to these two conditions. It help s the stronger company to grow faster than the competition and ensures quick swallowing of the weaker companies or them making irrelevant through exclusion (Sherman and Hart, 2006:1). Motives underlying M&A Different business enterprises and companies have used Mergers and Acquisitions as a means of growth strategies. ... The three differ according to the ideas behind them (Schmidt, 2010: 67) Economic motives Different authors have devised different theories to explain economic motives that encourage people to engage in Merges and Acquisitions; Efficiency theory This theory presents the motive of benefiting shareholders and managers of the acquiring company (Farschtschian, 2012:18). According to this theory, companies plan and execute Mergers and Acquisitions to achieve financial, operational and managerial synergies (Faulkner, Teerikangas and Joseph, 2012). The shareholders with this motive aim to benefit from net gains through synergy. Monopoly theory Under this theory, companies engage in Mergers and Acquisition with the motive of achieving market power. Mergers and Acquisitions under this motive may allow companies to cross-subsidize products, at the same time limit competitions in more than one market, and discourage potential entrants from the market. All of this result to monopoly power for the company. The shareholders under this motive aim at the wealth transfers from customers. Managerial Motives Theories that explain managerial motives include; Empire/Agency building theory This theory shows the motive aimed at benefiting managers. In this motive, managers plan for Mergers and Acquisitions aiming at maximizing their own utility instead of shareholders’ value (Karenfort, 2011: 9). The managers, according to this theory, plan to engage the company in mergers and Acquisition aiming at benefiting or creating their own reputation. Another motive is the need to transform to a corporate identity or recognition. This is where companies merge to gain popularity (Sherman and Hart, 2006:13). Financial motives The following theories explain the

What effect s can debt have on personal or professional relationships Essay

What effect s can debt have on personal or professional relationships Does this influence behavior Construct an argument to support your claim - Essay Example Depending on the debtor’s external conduct, work and friendship relationship tend to suffer. In most cases, debtors tend to feel that their friends or colleagues judge them because of their financial situations and behaviors, which could affect their social interactions qualities. Generally, debts triggers stress and tensions among people and in some cases, it results in constant fights hence creating unsafe environments (Wolny 58). Debts can have impacts personally or professionally. Professionally, debt can affects a worker’s overall work performance in that an individual can become inattentive or limited focus while performing his duties at the work place hence leading to job losses or financial problems (Wolny 59). Debtors usually feel socially controlled because they sometimes cannot afford their necessities, which might be an indirect pressure to them. As a result, this might affect their social standing. Alternatively, debts can influence a person’s behavior. In this case, a person’s self-worth might be affected which would then lead to emotional problems (Wolny 62). The inability of an individual to borrow could eventually lead to social problems. Numerous studies reveal that personal debt levels tend to be associated with related adverse health behaviors and poor psychological behaviors. One of the most common behaviors that might be influenced is stress. Stress remains the biggest mechanism through which debts can affect psychological health. Generally, a person’s stress experience can be related to the reduction of immune system functioning and the release of stress-related hormones. In most cases, they influence a person’s cardiovascular function and blood pressure. In some instances, the problematic personal debts and outcomes that are associated with it such bankruptcy can lead to a person’s decline in psychological health. Alternatively, some studies reveal that debts can lead to depression, suicidal cases and

Restaurant field experience report Essay Example | Topics and Well Written Essays - 500 words

Restaurant field experience report - Essay Example The beverage manager is responsible for preparing drinks orders for the entire day for dining service. I, therefore, managed beverage stock as required and ensured that they are paid for. The other major role that I had to take estimate how much beverage would be consumed on each day and place orders with the suppliers. Additionally, I had to check for fresh deliveries in order to maintain high quality. I also learned how to solve on clients complaints about the served drinks.As a receptionist, I was responsible for greeting guests, show them their tables and provide menus. I also provided customer service and deal with all inquiries in a courteous and professional manner, either via email or telephone. Additionally, providing information to guests on requests to ensure their comfort, safety and satisfaction were also a principal responsibility for me. During this period I learned to offer exquisite customer care service, to solve their inquiring and complaints made via email or tele phone. I also developed adequate communication skills and to be professional at all times while attending to guests.The efficiency of the kitchen of a restaurant rests on Expeditors. This is the person who is responsible for setting the pace and flow in the kitchen. On this post, I ensured that the orders made by guests were completed on time, according to the menu, and ensures they are in good quality for their satisfaction. I was also responsible relaying orders made to the kitchen.

Movies Assignment Example | Topics and Well Written Essays - 250 words - 1

Movies - Assignment Example The words further make the intention of the marketer controversial as they, one way of the other, promote and highlight supremacy and reign of White over the Black (Stuart, 2006). After watching this advertisement, the general perception I drew about the Whites was somewhat grand and physically powerful while the image of Blacks went down to slavery that was ever associated with them. Although it is an advertisement of gaming consoles, the idea about the racial differences remain an important part of this billboard advertisement making it questionable and unacceptable for many viewers. In my opinion, the advertisement is disrespectful to one race and provides a hidden meaning of superiority of Whites over the Blacks that remain discriminatory in its true essence. If someone was to learn about racial dynamics in the U.S. purely through this ad, he/she might think of blacks as socially lower class and disrespected people and Whites as dominant and powerful who may control

Perception of female leaders Thesis Example | Topics and Well Written Essays - 250 words

Perception of female leaders - Thesis Example This ideal would be wrongfully assumed to be true in general. In the same way that it is erroneous to presume that the current position of women has continued to progress backwards. In many industries it would be accurate to suppose that the trend of having ‘boy’s clubs’ is still at play. Businesses such as Information Technology and others that are similar in nature are well regarded as a majority men’s field. The ratio of men to women in population would no doubt be in favor of men. In such cases, it can be assumed that women will have a more arduous task in proving themselves in the workplace before they can gain the respect and opportunity to work in a higher position. This difference in gender is something that cannot be disregarded as such remains to be an underlying factor in and thus regarded deliberately in this paper. Women are identified towards what can only be regarded as instinctive leadership style in comparison to a more practical problem solving approach employed by men. This is not to say that one is extensively better than the other or vice versa. What it merely indicates is that there is a difference, nothing more and nothing less. Men and women are coexistent upon one another and both are fundamental in the workplace and in the broader spectrum of life. This is to say in a deductive manner that as constantly and as our creation suggests that men and women complement each other. In history, as the man hunts, the woman prepares the game and serves it to the family. Suppose that in the present the woman hunts and proves that she is as efficient, would her labor be regarded as any different? The answer is obvious and the answer is no. Just as the man was able to provide food in the table, the woman, in however diverse her hunting style may be supplied the same and equal nourishment for the household. If she turns out to be a good

Financial Strategy in the Emergent Countries Essay

Financial Strategy in the Emergent Countries - Essay Example Though, despite of vital up to date developments in hypothetical and to some point experiential, phases of the macroeconomics of economical policy, contemporary analyses have until at present failed to address the key issue of what establishes a nation's financial posture. (GREGORY, John Milton, 2008) In an expression, the dilemma is that economists for the majority of the time treat monetary policy as exogenous and deem the legislator to be similar to a programmable mechanism. Awfully there is very little literature available that addresses the issues like: Even very fewer studies have adapted contemporary economical analysis to solicit the category of institutions or lawful arrangements that will assist to sustain financial restraint and uphold stabilization efforts. (GREGORY, John Milton, 2008) The conventional literature on price increases in developing countries had paid attention on three core determinants of inflationary strains which are funds generation, economic imbalances and cost-push fundamentals. (GREGORY, John Milton, 2008) While the primary two aspects have been accentuated by the authors of a monitory influence, cost factors have played a decisive role in the structuralist theories urbanized throughout the 1950s-1960s. (GREGORY, John Milton, 2008) However, the majority of the current researches on price increases and stabilization have reallocated their concentration away from conventional direct economic causes of price increases such as funds creation, in the direction of political along with institutional determinants of inflationary forces. It is necessary for developing economies to focus on the methods like cost-shifting and externalities in array to maintain the pace of GDP growth rate in the times of global recession. (GREGORY, John Milton, 2008) This paper hereby highlights the significance and effects of cost-shifting and externalities in the economies of the developing countries. Cost-Shifting and Its Impacts An imperative characteristic as illustrated in diagram 2.2 is the relation among production and reproduction work in a social order structured around funds and earnings. As reproduction job is unwaged, the capability of viable institutions to valve into it provides growth to the likelihood to save capital and trim down costs. (DAHL, Robert Alan, 1992) It is evident that in this era of globalization the demands for cost reduction and increased efficiency have escalated from business institutions constrain to endure a viable conflict to governmental drive to trim down expenditures in array to struggle with a non-existent price increases. (DAHL, Robert Alan, 1992) There are majorly duo methods to trim down costs: 1. technological change 2. Cost-shifting "Technological change" entails the preamble of latest machinery that boosts labor efficiency and accordingly permits a diminution in unit cost. In a profit-driven civilization, this technological modification usually fallout in an employment affects i.e. amplification in unemployment

City Of London Investment Group PLC Coursework Example | Topics and Well Written Essays - 2250 words

City Of London Investment Group PLC - Coursework Example The main strategies adopted by the company are natural resource strategy, EM-Closed end funds strategy developed closed and strategy, human resource strategy, and frontier market funds strategy.Natural resources strategy is an important strategy of the organization. This strategy is geared toward attaining a long term capital growth by investing in corporations that get a large proportion of the profits from exploring, producing and offering services and technologies that are related to natural resources. The process of investment is fully integrated including bottom up, top down and thematic approaches. The process that involves the allocation of assets evaluates sector –specific, political and economic factors by using several sources of information including the company’s economists. Basing on on the satellite and core approach, the selection of stock is carried out through rigorous fundamental analysis whose horizon of return time is 12 to 18 months. Thematic analys is facilitates both stock selection and asset allocation elements of the process and assists the manager to exploit the wide range of opportunities in the natural resources sector while simultaneously realizing a diverse portfolio.The Emerging market closed- End funds strategy strives to offer a long term growth of capital through active country allocation and stock selection. The company believes that the closed-end fund provides an effective modality of investing in the emerging markets.

Moon Palace by Paul Auster Essay Example for Free

Moon Palace by Paul Auster Essay This is the story of Marco Stanley Fogg, an orphan searching for love, his father and the key to the riddle of his origin and fate. Marcos mother was killed in a car accident when he was eleven years old, and he never knew who was his father. Since then he had lived with his Uncle Victor in a small apartment on 112th Street in N.Y. His Uncle was a part of a band who was named Wally Moon and preformed at the Moon Palace diner. When Stanley grew up he went to the University; Uncle Victor gave him for this occasion a present, one thousand books. Afterwards, his Uncle had suddenly died. Then Stanleys situation became worse; He saw his money dwindle to zero, he lost the apartment and wound up living in the streets (He slept for three weeks in Central Park without food and with little money). His friends David Zimmer and Kitty Wu had found him and took care of him til he recover from his illness. Staley lived in Zimmers house until he had moved away to another apartment, then Stanley searched for a new place to live and found a job as a live-in companion for an elderly gentleman in a wheelchair. He lived with him for about half year until the gentleman died. His name was Effing Thomas but his real name was Julian Barber. In the past he was a famous painter but he stopped painting after the death of his brother and he changed his name after being considered dead by mistake. Stanley and Effing were very bonded since Effing was like the father Stanley never had. Dear Diary June, 1967 Today I was again in Broadway Street where was Chandlers Bookstore. I had sold him another box of Uncle Victors book. Sure, I had already read them. I know that they were the only memory, which was left from my uncle, buy I need the money to pay the rent and to buy some food and eat. August, 1968 Today I woke up early in the morning and got out to the street. As I was walking I saw that the drugstore had been opened already, I entered and I dropped a penny into the drugstore Exacto scale to see what was happening to me. From 154 in June, I fell to 139 in July and then to 123 in august. For someone who measured slightly over six feet, this began to be dangerously little. August, 1969 Today Fernandez, the owner of the building, threw me out my apartment. I took my knapsack with a few odds and ends, tucked the clarinet case, that Uncle Victor had left to me, and walked out the door I dont know what Ill do, or where do Ill go October, 1970 Now I have just finished to type down the life story of Effing on the typewriter that he had gave me. I have copied it from the notes I had taken in those nights when we sat down after supper. Me on the sofa and him in his wheelchair. He had told everything; Why had he changed his name and why did he choose this name (Effing), why did he stop painting, what happened to his wife and to his son. And eventually he told me that when he will die he wants his body to be cremated.

Health Issues in the Philippines Essay Example for Free

Health Issues in the Philippines Essay Like any other third-world country, the Philippines have been struggling in some health issues and one of it is illegal drug use. A lot of Filipinos are addicted to prohibited drugs. However, the Philippine government has dealt with this issue and although there are still some recorded incidents of drug abuse, the number of drug dependents in the Philippines has gradually decreased. One major health issue in the Philippines, is malnutrition. There have been studies conducted and accordingly, most of the Filipinos that suffer from malnutrition are the poor ones. The Philippine government, thru the Department of Social Welfare and Developments along with the Department of Health has provided projects to help poor Filipinos from starvation. Other health issues in the Philippines are dengue cases, but then, these health concerns are only happening in the rural area of the country. Most of these cases are properly attended to by the Philippine government Health issues in the Philippines The Philippines have been struggling with some healthcare issues, one of the most noticeable being illegal drug use.There are a number of Filipinos who are said to be addicted to prohibited drugs. However, the Philippine governmenthas concentrated on this issue and although there are still some recorded incidents of drug abuse, the number of drug dependents has gradually decreased.Another serious health issue is malnutrition. Unsurprisingly, the poorer citizens are the ones who suffer from thiscondition. The Philippine government, through the Department of Social Welfare and Development and in conjunction with the Department of Health, has initiated projects to help its poorer citizens who suffer from starvation.Cases of dengue are also notable. However, most of these cases are properly attended to by the Philippine government.

Approaches to Flat Slab Design

Approaches to Flat Slab Design Abstract This dissertation aims at the flexure behaviour of reinforced concrete flat slabs in the elastic range and at the ultimate load. As such, it endeavours to give readers a thorough knowledge of the fundamentals of slab behaves in flexure. Such a background is essential for a complete and proper understanding of building code requirements and design procedures for flexure behaviour of slabs. The dissertation commences with a general history background and the advantages of using flat slab as the type of floor construction. After that, an introduction of various slabs analysis method as well as the determination of the distribution of moments using elastic theory will be discussed. The building code based methods like ACI direct design method, Simplified coefficient method for BS8110 and EC2 and Equivalent frame method will be explained in details. After that follows a detailed of limit procedures for the ultimate analysis and design of flat slab using general lower bound theory for strip method and upper bound theory for yield line analysis. Besides, the fundamental of the finite element method will be discussed as well. Then, analysis will be carried out on a typical flat slab panel base on each design approach available such as yield line method, simplified coefficient method, direct design method, finite element method as well as Hillerborg strip method. The flexure resistant obtained from the analysis result will then be compared among each others and highlighting the possible pros and cons of the different analysis. Eventually, the analysis results will then be discussed in order to conclude a rational approach to flat slab design and further recommendation will be given to the future improvement of this research. 1. Introduction Concrete is the most widely used construction material in the world compare to steel as concrete is well known as the most versatile and durable construction materials. In fact, concrete is also one of the most consumed substances on Earth after water [1]. Concrete has played a major role in the shaping of our civilization since 7,000 BC, and it can be seen everywhere in our built environment, being used in hospitals, residential buildings, schools, offices, industrial buildings and others [2]. Nowadays, construction should not just be about achieving the cheapest building possible, but providing best value for the client. The best value may be about costs, but also includes speed of construction, robustness, durability, sustainability, spacious environment, etc. In fact, many type of concrete floor construction can easily fulfilled the above requirements. In the past, forming the concrete floor construction into shape was potentially the most costly and labour intensive part of the process. Nowadays, with the help of modern high efficiency modular formwork has speed up the concrete floor construction process. Alternatively, floor slab elements may be factory precast, requiring only assembly, or stitching together with in-situ elements. The result is an economic and swift process, capable of excellent quality and finishes to suit the buildings needs. 1.1 Types of concrete slab construction Concrete slab floor is one of the key structural elements of any building. Concrete floor choice and design can have a surprisingly influential role in the performance of the final structure of the building, and importantly will also influence people using the building. In general, cost alone should not dictate slab floor choice in the construction. However, many issues should be considered when choosing the optimum structural solution and slab floor type that give best value for the construction and operational stages. The optimum slab floor option should inherit benefits such as fabric energy storage, fire resistance and sound insulation between floors and others as achieving these requirements will eventually help the concrete building to lower the operation costs and maintenance requirement in long term. In general, reinforced concrete slab floors can be divided into three categories as detailed below: Flat slab Flat slab is also referred to as beamless slab or flat plate. The slab systems are a subset of two-way slab family, meaning that the system transfer the load path and deforms in two directions. It is an extremely simple structure in concept and construction, consisting of a slab of uniform thickness supported directly by the columns with no intermediate beams, as shown in Figure 1.1. The choice of flat slab as building floor system is usually a matter of the magnitude of the design loading and of the spans. The capacity of the slab is usually restricted by the strength in punching shear at the sections around the columns. Generally, column capitals and drop panels will be used within the flat slab system to avoid shear failure at the column section when larger loads and span are present, as shown in Figure 1.2. Figure 1.1: Solid flat slab Figure 1.2: Solid flat slab with drop panel Flat slab is a highly versatile element widely used in construction due to its capability of providing minimum depth, fast construction and allowing a flexible column grid system. Slabs supported on beams One-way spanning slabs are generally rectangular slabs supported by two beams at the opposite edges and the loads are transferring in one direction only. Figure 1.3 shows the type of one-way slabs. Deep beam and slab Band beam and slab Figure 1.3: Type of one-way slabs However, slab supported on beams on all sides of each panel are generally termed two-way slabs, and a typical floor is shown in Figure 1.4. Figure 1.4: Two-way slab The beams supporting the slabs can generally be wide and flat or narrow and deep beam, depending on the structures requirements. Beams supporting the slabs in one or two way spanning slabs tend to span between columns or walls and can be simply supported or continuous. In this beam-slabs system, it is quite easy to visualize the path from the load point to column as being transferred from slab to beam to column, and from this visualization then to compute realistic moments and shears for design of all members. This form of construction is commonly used for irregular grids and long spans, where flat slabs are unsuitable. It is also good for transferring columns, walls or heavy point loads to columns or walls below. This method is time consuming during the construction stage as formwork tends to be labour intensive [3]. Ribbed and Coffered slabs Ribbed slabs are made up of wide band or deep beams running between columns with equal depth narrow ribs spanning the orthogonal direction. Loads are transferring in one direction and a thin topping slab completes the system, see Figure 1.5. Ribbed with deep beam Ribbed with wide beam Figure 1.5: Types of ribbed slabs Coffered slab may be visualized as a set of crossing joists, set at small spacing relative to the span, which support a thin slab on top. The recesses in the slab usually cast using either removable or expendable forms in order to reduce the weight of the slab and allow the use of a large effective depth without associated with slab self weight. The large depth also helps to stiffer the structure. Coffered slabs are generally used in situations demanding spans larger than perhaps about 10m. Coffered slabs may be designed as either flat slabs or two-way slabs, depending on just which recesses are omitted to give larger solid areas. Figure 1.6 shows the types of waffle slabs. Coffered slab with wide beam Coffered slab without beam Figure 1.6: Type of coffered slabs Ribbed and coffered slabs construction method provides a lighter and stiffer slab, reducing the extent of foundations. They provide a very good form where slab vibration is an issue, such as electronic laboratories and hospitals. On the other hand, ribbed and coffered slabs are very consuming during the construction stage as formwork tends to be labour intensive [3]. 1.2 Flat slab design as the choice of research The choice of type of slab for a particular floor depends on many factors. Cost of construction is one of the important considerations, but this is a qualitative argument until specific cases are discussed. The design loads, serviceability requirements, required spans, and strength requirement are all important. Recently, solid flat slab is getting popular in the construction industry in Europe and UK due to the advantages as below: Faster construction Construction of flat slabs is one of the quickest methods among the other type of floors in construction. The advantages of using flat slab construction are becoming increasingly recognised. Flat slabs without drops (thickened areas of slab around the columns to resist punching shear) can be built faster because formwork is simplified and minimised, and rapid turn-around can be achieved using a combination of early striking and flying systems. The overall speed of construction will then be limited by the rate at which vertical elements can be cast [4]. Reduced services and cladding costs Flat slab construction places no restrictions on the positioning of horizontal services (eg. mechanical and electrical services which mostly running across the ceiling) and partitions and can minimise floor-to-floor heights when there is no requirement for a deep false ceiling. In other words, this helps to lower building height as well as reduced cladding costs and prefabricated services [4]. Flexibility for the occupier Flat slab construction offers considerable flexibility to the occupier who can easily alter internal layouts to accommodate changes in the use of the structure. This flexibility results from the use of a square or near-square grid and the absence of beams, downstands or drops that complicate the routing of services and location of partitions [4]. Undoubtedly, flat slab construction method is getting popular but there are still many different views about what constitutes the best way of reinforcing concrete in order to get the most economic construction. In addition, a range of methods is available for designing the flat slab and analysing them in flexure at ultimate state. Different analysis and design methods can easily result in variety of different reinforcement arrangements within a single slab, with consequent of making the different assumptions in each analysis and design method. Therefore, this research project will concentrate in examining the various analysis methods for the design of flexural reinforcement of reinforce flat slabs in terms of the code provisions, yield line analysis as well as finite element analysis method. 1.3 Research objectives Reinforced concrete slabs are among the most common structural elements, but despite the large number of slabs designed and built, the details of elastic and plastic behaviour of slabs are not always appreciated or properly taken into account especially for flat slab system. This happens at least partially because of the complexities of mathematic when dealing with elastic plate equations, especially for support conditions which realistically approximate those in multi-panel building floor slabs. Because the theoretical analysis of slabs or plates is much less widely known and practiced than is the analysis of elements such as beams, the provisions in building codes generally provide both design criteria and methods of analysis for slabs, whereas only criteria are provided for most other elements. For example, Chapter 13 of the 1995 edition of the American Concrete Institute (ACI) Building Code Requirements for Structural Concrete, one of the most widely used Codes for concrete design, is devoted largely to the determination of moments in slab structure. Once moments, shear, and torques are found, sections are proportioned to resist them using the criteria specified in other sections of the same code [5]. The purpose of this research project is to examine the analysis methods such as Hillerborgs strip, yield line analysis, equivalent frame method, finite element method and etc. particularly for the design flexural reinforcement of reinforced flat slabs, and meanwhile to gain full understanding of the theories. The different analysis methods will then be analysed and compared with the flexural capacity method calculated using general codes of ACI 318 [5], Eurocode 2 [6] and BS8110 [7]. The outcomes of the comparison will lead to highlight the pros and cons of different approaches and codes paving the way to find out a rational approach for the flat slab design in flexure. The main objectives of the proposed research are: To examine the different methods and codes use to handle the flexural capacity of the slab. To outlined the different positive and negative aspect in a specific code or method of design To gain full understanding of the flexural design theories and code requirements. To highlight the most economical design solution to overcome the flexure in a flat slab while maintaining the safety as code requirements. 1.4 Research dissertation methodology The following will be the proposed methodology of the research dissertation: Background of flat slab in construction industry Research of the evolution of flat slabs in the past decades and the major contributions made for the construction industry. Difficulties faced during the flexure design of flat slabs in the past and the possible solution for the problems will be discussed. This part of research process result in closer to the background history and the revolution of flat slab in construction. Overview of flat slab design methods Examine each design approaches used to design for flexure in flat slab such as yield line analysis, Hillerborgs strip method, the simplified coefficient method for BS8110 or Eurocode 2 and direct design method for ACI. An insight into different methods and codes will help to establish and revise the general code provisions and also gain the full understanding of theory and design of flat slab. Analysis of flat slab with different approaches Different analysis and design approaches for flexural reinforcement of RC flat slabs will be performed based on the same model slab. For instance, finite element computer software packages will be used to perform the finite element analysis. This part will eventually provide a deep understanding of various design methods as well as the ability to use finite element software in analysis and design. Research the flexural pros and cons in a flat slab among each design methods to get the rational design approach. Discussion The numerical analysis results obtain from different design methods and the codes will be discussed and compare among each others and also to the experimental results obtain in the previous research papers such as Engineering journals and other relevant engineering sources. This process will ultimately lead to a proper and systematic comparison of the codes and methods used, and highlighting their pros and cons. Conclusion This part will conclude the discussion on advantages and disadvantages of all the examined design methods trying to establish which design method may result in a more economic and rational solution. Furthermore recommendations if required and the possible future areas of research will be brought up. 1.5 Dissertation layout Chapter 2 Overview of Design This section will cover the brief of the evolution of flat slabs history. Brief introduction to the current codes for flat slab design such as American Concrete Institute ACI-318, British Standard BS8110 and Eurocode 2. In addition, the fundamental of analysis and flexure strength requirement of each code will be briefly described. Brief introduction to design methods and history of yield line analysis, Hillerborgs strip method and finite element analysis in the slab flexure design. Chapter 3, Analysis Introduction of the analysis process and assumption made for each analysis methods. Focusing on different numerical aspects of the design under different codes and approaches. This section will provide deep understanding of various design methods and how the methods deal with the flat slab flexure problem. Chapter 4, Discussion Comparison between different code equations and theories. Various numerical result from different approaches will be compared and discussed based on the experimental results from past research papers. Pros and cons of different methods for design codes (eg. ACI, EC2 and BS8110), Hillerborg strip method, yield line analysis Graphs and tables will be available to show the summary of the results from different methods. Chapter 5, Conclusion Summarise the economic and rational flexural design approach for flat slab Further recommendations 2. Overview of Design Method The aim of chapter 2 is to provide an overview of the current practice of the design of reinforced concrete flat slab systems. General code of practice of ACI 318, EC2 and BS 8110 requirements are presented, along with the brief of the ACI direct design method, EC2/BS8110 simplified coefficient method, equivalent frame method, yield line, Hillerborgs strip method as well as finite element method. Each procedure and the limitations are discussed within. The following discussion is limited to flat slab systems. That is, the design methodologies presented below relate only to slabs of constant thickness without drop panels, column capitals, or edge beams. In addition, prestressed concrete is not considered. 2.1 Approaches to the analysis and design of flat slab There are a number of possible approaches to the analysis and design of reinforced concrete flat slab systems. The various approaches available are elastic theory, plastic analysis theory, and modifications to elastic theory and plastic analysis theory as in the codes (eg. ACI Code [5]). All these methods can be used to analyse the flat slab system to determine either the stresses in the slabs and the supporting system or load-carrying capacity. Alternatively, these methods can be used to determine the distribution of moments to allow the reinforcing steel and concrete sections to be designed. 2.1.1 Elastic theory analysis Conventional elastic theory analysis applies to isotropic slabs that are sufficiently thin for shear deformations to be insignificant and sufficiently thick for in-plane forces to be unimportant. The majority floor slabs fall into the range in which conventional elastic theory is applicable. The distribution moments forces found by elastic theory is such that: Satisfied the equilibrium conditions at every point in the slab Compliance with the boundary conditions Stress is proportional to strain; also, bending moments are proportional to curvature The governing equation is a fourth-order partial differential equation in terms of the slab deflection of the slab at general point on the slab, the loading on the slab, and the flexural rigidity of the slab section. This equation is complicated to solve in many realistic cases, when considering the effects of deformations of the supporting system. However, numerous analytical techniques have been developed to obtain the solution. In particular, the use of finite difference or finite element (FE) methods enables elastic theory solutions to be obtained for slab systems with any loading or boundary conditions [8]. Nowadays, with the advancement of computer technology software, designer can easily obtained the bending and torsional moments and shear forces throughout the slab easily with any finite element software packages such as ANSYS, LUSAS, STAAD PRO, SAP2000 and others. 2.1.2 Plastic analysis The plasticity, redistribution of moments and shears away from elastic theory distribution can occur before the ultimate load is reached. This redistribution occur because for typical reinforced concrete section there is little change in moment with curvature once tension steel has reached the yield strength. Therefore, when the most highly stressed sections of slab reach the yield moment they tend to maintain a moment capacity that is close to the flexural strength with further increase in curvature, while yielding of the slab reinforcement spreads to other section of the slab with further increase in load. To determine the load carrying capacity of rigid-plastic members, two principles are used as below: Lower Bound Theorem states that if for any load a stress distribution can be found which both satisfies all equilibrium conditions and nowhere violates yield conditions, then the load cannot cause collapse. The most commonly used approach is Hillerborgs Strip method [9]. Upper Bound Theorem states that if a load is found which corresponds to any assumed collapse mechanism, then the load must be equal to or greater than the true collapse. Finding a load which may be greater than the collapse load may be considered to be an unsafe method; however, because of membrane action in the slab and the strain hardening of the reinforcement after yielding, the actual collapse load tends to be much higher. The commonly used approach of this method is yield line theory [9]. 2.2 Early History and Design Philosophies Credit for inventing the flat slab system is given to C.A.P. Turner for a system describe in the Engineering News in October 1905. However, the first practical flat slabs structure, Johnson-Bovey Building was built in 1906 in Minneapolis, Minnesota, by C.A.P. Turner. It was a completely new form of construction, and in addition there was no acceptable method of analysis available at that time. The structure was built at Turners risk and load-tested before hand in to the owner. The structure met its load test requirements hence the flat slab system was an instant commercial success and many were built in the United States later on [10]. Robert Maillart was also one of the founding fathers of flat slab from Europe, a design-and-built contractor who was perhaps better known for his work on the design of Reinforced Concrete Bridge. In 1908 Malliart carried out a series of full-scale tests on his flat slab system, see Figure 2.1. About the same time, Arthur Lord, a research fellow at the University of Illinois, also became interested in understanding how flat slabs behaved. In 1911, Lord obtained approval to instrument and test load a seven-storey flat slab building in Chicago. The view and work by them paves the way for the development of flat slabs. Their work evolved into a codified method of design and in 1930 became the London Building Act [11]. Then, Robert Malliarts dimensioning method is reviewed and compared with methods of elastic plate theory and plastic analysis. When compared the results with as elastic analysis, Malliart method considerably underestimate the bending moments acting for the flat slabs. However, the comparison made on limit analysis procedures, Malliarts design is still within the reasonable safety margins [12]. Figure 2.1: First test on flat slabs carried out in 1908 at Maillart Co. works in Zurich [11] In 1878, Grashoff have tried to use polynomial approximation deflection function to work out the flat slab design but was unsuccessful to satisfy certain boundary conditions. At that time, concrete flat slab was emerged in the use as boiler cover plates for steam engines. Due to this problem, in 1872, Lavoinne was forced to work out the flat slab using the Fourier series. Lavoinne assumed a uniformely load is loaded on an infinite large plate and the plate is under simply supported conditions. In this assumption, Lavoinne neglected the poissons effect but Grashoff did consider [12]. Maillart was aware of Grashoffs approach but he thought that it was useless for his purpose because it was restricted to uniformly distributed loads and did not account for the stiffening effect of columns. Based on simple equilibrium considerations, Nicholas managed to prove that all these systems resulted insufficient reinforcement [12]. In the year of 1921, Westergaard and Slater managed to develop a new flat slab theory by comparing the theory results to the available experimental results at that time. In the theory, the stiffening effects due to the presence of columns under different load condition were discussed. Marcus had considered this theory later on by applying finite differences approach; Marcus assumed few different boundary conditions and loads. During the past, due to the absence of a proper theory for flat slab design in Germany hence flat slab construction was almost impossible to be carried out. After sometime later, requirements for the flat slab design theory were established. This theory again mentioned that the design moment must follow Lewes theory (1920, 1922) or theory developed by Marcus (1924). [12]. 2.2.1 Robert Maillarts Contribution In 1902, Maillart has successfully developed dimensioning procedure to design a flat slab. This method was used and succeeds in building few numbers of large flat slabs structure. Due to the absence of strict construction rules in Switzerland, Maillart managed to design flat slab by considering the principle of superposition and successfully performed several arbitrary loads testing on flat slabs. Maillart derived the flexure moments at intermediate points by multiplying the flexural stiffness of the slab with the respective curvatures. The curvatures were derived using the double differentiation of the eight-order polynomial functions meanwhile the flexural stiffness of the slab was analysed using simple one way flexure test on respective slab strips [12]. Maillarts reinforcement pattern for flat slab was very close to the current design approaches. Maillarts method required to reinforce the slab in only two directions. However, C.A.P. Turner insisted to reinforce the slab in four directions (see section 2.2.2 for details). Maillart dimensioning procedure emphasised in designing for positive moments at three different locations labeled as O, Q, and C in Figure 2.2 (where O at the midspan, Q at the quarter point of transverse span l2, and C in the column axis). Negative moments were not checked in Maillart dimensioning procedure and all the bottom bars were simply bent up in the columns strips. In this method, the span ratios, size of column capital and the minimum height of the column capital were restricted to certain values, limiting the nominal shear stress at the circumference of the column to a permissible value [12]. Figure 2.2: Robert Maillarts system and notation for plan view [12] Later, Maillarts results were found underestimated with elastic analysis method. In addition, Maillarts method predicts a reduction in average moment value corresponding to span ratio while elastic plate theory remaining constant. Maillarts method underestimated elastic moments especially for a very large slab structure. In other words, Maillarts dimensioning method has significant differences with elastic analysis procedure in the flexure result of slab [12]. Since Maillarts dimensioning method ignored the negative moments hence this worries the designer when came to the safety of the slab design. In conclusion, Maillart underestimated the moments compared to the elastic analysis on the other hand similar approach to the limit analysis [12]. 2.2.2 C.A.P. Turners Concept Turner never published complete details of his design methods in order to maintain a competitive advantage in the design industry. However, some insights of Turners conceptual design of his flat slabs are available in his patent applications (C.A.P. Turner, Steel Skeleton and Concrete Construction and Elasticity, structure and strength of materials used in engineering.) [10]. In fact, Turners principle design was more concerned about shear in flat slabs as stated by him, Beside the unreliability of concrete in tension, it is unreliable in shear in its partially cured condition. This renders desirable use of reinforcement near the columns or supports to take care of shear [10]. In Turners principle, a so called Mushroom heads or cantilever caps were designed to provide shear resistance in flat slabs. As quoted by Turner, heads may be constructed in accordance with the shearing strain. The diameter of cantilever head was about one-half of the span length. Turner presumed the reinforcement cage acted as part of cantilever support to the slab [10]. Figure 2.3 is an example of the cantilever support mentioned by Turner. Figure 2.3: C.A.P. Turner, mushroom or cantilever shear head [10] Besides shear, Turner also focused on moments and used a four way reinforcement which also known as reinforcement belts, see Figure 2.4. These belts have the same width as that of the cantilever shear head. Turner believed that the positive moments were small due to the cantilever support which is stated as, Referring to flat central plate, or the suspended slab portion, there is practically no bending moment at the center [10]. Figure 2.4: C.A.P. Turners four belt floor reinforcement system [10] Also, Turner believed reinforced the slab in four directions (four belt floor reinforcement system) would provide the moment resistance to counter the negative moments at supports. With these conceptions, Turner considered a very small total design moment to proportion the flexural steel in the four belts. Turner simplified the equation as following: (1) where, W = total dead and live load in one bay L = nominal dimensions in one bay As = total flexural steel, distributed among the four belts fs = allowable steel stress d = distance to tension reinforcement Turner used the co-efficient of 1/50 for equation (1) above reference to Grashoff (1878) and to Prof. Henry T. Eddy (1899) from University of Minnesota. In fact, Turner decided to use such a small coefficient due to the consideration of shorter effective span between cantilever heads. Moreover Turner also considered the slab spanning continuously instead of simply supported design. Numerous experiments data performed by Turner proved that such a coefficient was sufficient for flexure resistant. Besides, the use of cantilever head lead to the unnecessary of drop panels in Turners concept. Turners design concept has successfully built many buildings and bridges from year 1905 to 1909 [10]. 2.3 Current Methods of Flat Slab Design 2.3.1 American Concrete Institute (ACI) American Concrete Institute (ACI) is one of the oldest codes and widely been used to design for reinforced concrete structures. The code covers a number of methods to design a flat slab system. The design of structural concrete is dictated by Building Code Requirements for Structural Concrete (ACI 318-05) and Commentary (ACI 318R-05). The ACI code contains procedure for the design of uniformly loaded reinforced concrete flat slab floors. These methods are direct design techniques and equivalent frame method. All these methods are based on analytical studies of the distribution of moments using elastic theory and strength using yield line theory, the results of tests on

Slavery position with writers :: essays research papers

The issue of slavery in the nineteenth century produced an overwhelming issue in society. There were some writers that favored slavery and then there were some that did not favor slavery. In favor of slavery were William Gillmore Simms, and Caroline Hentz. Those opposed to slavery were Frederick Douglass, Harriet Beecher Stowe, Henry David Thoreau, and Herman Melville. All of these writers presented their views of slavery in the their literary works.   Ã‚  Ã‚  Ã‚  Ã‚  William Simms was a supporter of slavery and this evident in his novel, â€Å"Woodcraft.† This novel takes place in the south during the closing of the Revolutionary War. Simms was born in Charleston, South Carolina, so he was raised on the souths’ position of pro-slavery. In Simms novel Woodcraft, he states, â€Å" Exhaustion not wisdom, or a better state of feeling, was the secret of the peace which was finally concluded between the two nations (America and Great Britain), and of which, South Carolina, and Charleston in particular, was eagerly expecting the benefits. (Simms 35) Great Britain had spent most of the Revolutionary War occupying Charleston and the soldiers would stay at the peoples’ home with out the homeowners consent. This angered many townspeople in Charleston and many other townspeople throughout the south. Since the war was coming to an end the people of Charleston could have their city and homes again. Also meaning plantat ion owners and slaver owners could resume back to their work of the land, which was the major source of economy in the south. During the Revolutionary War, Great Britain was re-stealing the slaves of slave owners in the south. In â€Å"Woodcraft,† it is stated, â€Å" South Carolina had already lost twenty-five thousand slaves, which British philanthropy had transferred from the rice-fields of Carolina to the sugar estates of the West India Islands; and there were yet other thousands waiting to be similarly transported.† (Simms 35,36) Great Britain was taking slaves from America to use for their sugar estates. Many slave owners were very angry with the British for this, but in hindsight the slave owners had done the same thing when they would take slaves from their families or would split slaves families up. Carolina Hentz was also a supporter of slavery. She believed that the slaves were treated well and that they were best suited as slaves. Hentz uses examples in her novel, â€Å"The Planter’s Northern Bride,† as to how well treated slaves were.

Malcolm X Essay -- essays research papers

The 1950’s and 1960’s were decades full of powerful speakers. These speakers could motivate people in such a strong way. They were a huge part of the Civil Rights Movement being successful. One of these powerful speakers was Malcolm X. He led a very interesting, yet tragic life.   Ã‚  Ã‚  Ã‚  Ã‚  Malcolm X was born Malcolm Little on May 19, 1925 in Omaha, Nebraska. He was one of eight children. His mother, Louise Norton Little, was a homemaker while his father, Earl Little, was a Baptist minister. His father was a devoted follower of Marcus Garvey, who was the Black Nationalist leader. Malcolm had already moved twice by the time he was four because of threats aimed towards his father from white supremacy groups. Earl tried to get his family away from groups like the Black Legion but despite his efforts, the Legion burned down their house in Lansing, Michigan in 1929. In 1931, Malcolm’s father’s body was found mutilated on the town’s trolley tracks. Even though both incidents were ruled by police, the family knew the Black Legion was behind them both. Louise had a very hard time with the death of her husband. A few years after he died, Louise broke down and was committed to a mental institution. Because of this, all eight children were split up into various foster homes.   Ã‚  Ã‚  Ã‚  Ã‚  Malcolm was always a very smart student. In junior high, he was at the top in his class. Malcolm went through some hardships in school though. One of his favorite te...

American Industrialization Essay -- American History

Between 1865 and 1920, industrialization caused significant changes in many people’s lives. First, the development of a new railroad system help settle the west and made it more accessible to people. Second, public transit systems in big cities provided an outlet from congested cities. Last, the discovery of a method for transmitting electricity helped to light up our daily lives. I feel that these are three of the most important changes in people’s lives caused by industrialization. First, the building of railroads out west played a huge part in the successful expansion of our country and the fulfillment of American dreams. Priot to the development of a more efficient railroad system, the movement of people and freight were relatively slow, difficult, and costly. Because of different rail gauges, sometimes freight had to be unloaded and then reloaded on boxcars. Second, most goods had to be produced and provided locally on a small scale. As a result, prices for products were very high. Nevertheless, with the help of federal grants, railroad promoters were able to build a more efficient railroad system that would connect the settled east with the unsettled west. After the completion of the new railroads system, farmers were in reasonable distance of railroad depots, which meant manufacturers could locate their plants anywhere and be able to bring in raw materials and send their products wherever they could find customers. Also, freight and passengers could travel by rai...

An internal locus of control Essay

An internal locus of control is â€Å"the belief that one’s fate is determined by one’s own behavior. † While the external locus of control is â€Å"the belief that what happens is determined not by one’s own actions but by powerful others, luck, and external forces† (Kassin and Wrightsman 1988, 32). What this is saying is that the psychological process of defining the reasoning behind why someone is doing something is that there is either an internal or external locus of control that is determining the factors around the individual. According to the book on page 313 there are times when a judge can decide that a person who has a particular background, occupation or situation would not be a good juror for a trial. This is because their internal locus of control could sway their decision making ability based on what they know and what they have utilized in their profession. In one instance that was described in the book there were two jurors that were kept out of a trial based on their own internal locus of control. One of these jurors was a scientist while the other worked in credit management. Based on the case it was considered that these two potential jurors might not be able to look at the situation completely unbiased and therefore these two jurors were let go from the jury. This is one example on how an internal locus of control can affect someone who is a potential juror (Greene, Heilbrun, Fortune, and Nietzel 2006). A way that the external locus of control can affect someone who is a juror is a bit different. What this means is that someone is being influenced by outside influences which would make them biased in some way to the decision making process. According to the book on page 303 there is a discussion about the interviewing that occurred in the O. J. Simpson trial when looking for jurors. The overwhelming conclusion was that there was a prevalence for African American women to think that some forms of abuse were okay in relationships and this is an external influence to their overall opinions of things. Therefore this influence could influence how the jurors felt about the abuse that O. J. ’s wife had suffered from and therefore they might have a bias (Greene, Heilbrun, Fortune, and Nietzel 2006). Provide an opinion on whether jurors are able to disregard inadmissible evidence using theories discussed in the text, why or why not? According to the book on pages 338-340 there are a number of ways that a juror can look into disregarding evidence that has been determined to be inadmissible. Whether or not this is really possible is a different story. The text describes some different ways that the evidence can be disregarded. These include the reactance theory which is if instructed to disregard certain information the overall decision making ability of the juror could be compromised. Through this theory it is common that someone would use some type of thought suppression to block the material from their thoughts. It is thought that even though this material has been marked as inadmissible that it could possibly still influence the jury’s overall decision (Greene, Heilbrun, Fortune, and Nietzel 2006). In my opinion it could be possible for a juror to disregard inadmissible information however it would be very difficult and it might cause problems for the individual as well. It would be difficult to forget something that was mentioned if it was something that would strongly influence one’s decision however if it was material that was not a big deal then it would not be likely that this would have much influence. In one study that was conducted jurors who were given proacquittal inadmissible information were less likely to convict than those who were given proconviction inadmissible information (Thompson, Fong, and Rosenhan 1981).

A Stylistic analysis of ‘Under Milk Wood’ by Dylan Thomas

A Stylistic analysis ofUnder Milk Woodby Dylan Thomas. by Dylan Thomas. The object of this paper is to stylistically analyzeUnder Milk Wood( 1954 ) by Dylan Thomas. I aim to determine what Thomas’s influences upon his work were and how he uses literary techniques to make a piece of literary art which is so appealing to the senses. I will besides associate these repeated stylizations to Thomas’s historical and cultural background in order to derive a full image of his life at the clip of composing. Dylan Marlais Thomas was born on the 27Thursdayof October, 1914 in Swansea, Wales. Thomas is responsible for a immense organic structure of work during his short life ; nevertheless, his most celebrated piece of authorship isUnder Milk Woodwhich was published in 1954.Under Milk Woodis non merely Dylan Thomas ‘ most celebrated piece of work, but it was besides his last. During his childhood, Thomas spent the bulk of his life in his place town, nevertheless, each summer he was sent off to his aunt’s house in Carmarthenshire farms. This allowed Thomas to see the contrasting side to that of his busy town life and proved to hold a immense impact on the manner in which he wrote. Thomas attended Swansea Grammar School from 1925 and whilst at that place, he began to maintain diaries of poesy which he had written, and his first verse form was published in the school magazine. By the clip Thomas left school at the age of 16, he had already written over 200 verse forms. ( Poemhunter: 2014 ) As a kid, Thomas frequently had reoccurring eruptions of bronchitis and suffered from terrible asthma ( Bio: 2013 ) , as a consequence, he was seen as excessively weak to contend in World War II and was alternatively used to compose authorities books. However, Thomas found it hard to populate off the little rewards and sought employment with a company named Strand Films. Strand Films created short productions for the Ministry of Information and Thomas wrote five of these in 1942. During this clip, Thomas was roll uping a aggregation of verse forms, one of which was subsequently published in 1946 asDeath and Entrances. This aggregation of verse form was inspired by World War II and trades with the effects which arise from war and was dubbed as the devising of his calling. Critic Walter J. Turner said that ‘this book entirely, in my sentiment, ranks him as a major poet’ ( 1946: 176 ) . In 1941, Swansea was bombed by the German Luftwaffe, and Thomas saw the devastation of t he streets which he held beloved to his bosom and this inspired him to compose about this experience in a wireless drama which he called,Return Journey Home( 1958 ) . The Second World War appears to hold been a big influence uponUnder Milk Woodand the creative activity of Llareggub was Thomas’s manner of making ‘a picturesque sense of the past’ ( 1995: 19 ) where clip had been at a standstill as ‘the custodies of the clock have stayed still at half past 11 for 50 years’ ( 1995: 28 ) . This gives the audience the vision of a town where clip does non count and war has non been a calamity which the citizens have been forced to meet. In 1950, Thomas was invited to New York by John Malcolm Brinnin in order to tour the humanistic disciplines Centres in America, over a three month period. Two old ages subsequently in 1952, Thomas embarked upon the humanistic disciplines tour one time once more, this clip with his married woman, Caitlin Macnamara. Whilst in America, Macnamara discovered that Thomas had been unfaithful on his old trip to the States and the brace began to imbibe to a great extent and reason unrelentingly ( Poemhunter: 2014 ) . The heavy imbibing caused Thomas’ wellness to deteriorate and he shortly found himself enduring from urarthritis and external respiration troubles. On the 3rdof May, 1953, whilst in America, Thomas preformed an unfinishedUnder Milk Wood( 1954 ) at Harvard University on his ain. He so performed once more, this clip with a full dramatis personae of histrions, at The Poetry Centre in New York on the 14Thursdayof May 1953.Upon his return to Wales, Thomas completed the drama an d it was performed to the full for the first clip at The Lyric Theatre in Carmarthen, Wales on the 8Thursdayof October 1953. On the 19Thursdayof October, 1953, Thomas flew back to America in order to execute the finished drama, nevertheless, unluckily, on the 5Thursdayof November, 1953 ; Thomas was admitted to St. Vincent’s infirmary after a tally of bad wellness, with ‘acute alcoholic encephalopathy’ ( Poemhunter: 2014 ) and slipped into a coma before go throughing off on the 9Thursdayof November 1953. The calamity of his passing besides meant that the BBC was now unable to get down with the cinematography ofUnder Milk Woodwith Thomas as the voice ( 1954 ) . ‘A Play for Voices’ is the caption ofUnder Milk Woodand this helps to determine the genre of it highly good. Although the drama was specifically written to be a wireless production, it is non a typical drama. The most important divergence from the normalcy of a drama is that it is unusual for a drama to hold a storyteller. In a phase drama, the ideas, feelings and scenes are conveyed straight to the audience via the characters utilizing duologues and monologues. It is obvious that the drama is a dramatic production and contains all of the properties which we would anticipate to happen within a dramatic text. A play is a text which is written to be performed on phase, telecasting or wireless and will include: staging waies, character lists, waies for costumes, and is written to be performed in the signifier of a duologue book.Under Milk Wooddoes incorporate all of these characteristics, but besides contains facets of poesy and narrative which are unusual characteristics o f serious play. Under Milk Woodis set in a fancied town in Wales which is called Llareggub. Although the town name really sounds Welsh, it is in fact the backwards spelling of the term sodomite all. The drama illustrates the life of Llareggub ‘s occupants over the infinite of a dark from ‘spring, moonless night’ ( 1995: 3 ) to ‘the thin dark darkness’ ( 1995: 62 ) . The drama contains no existent action but does incorporate different episodes which are connected by the two omniscient storytellers, the ‘first voice’ ( 1995: 3 ) and the ‘second voice’ ( 1995: 4 ) . These two voices displacement from character to character but they do non truly belong to the citizens of Llareggub. The voices merely present the characters to the hearer so in consequence ; they are mediators for the audience and the dramatic subdivisions of the drama. The drama contains many different poetic effects, which are largely spoken by the ‘First Voice’ ( 1995: 3 ) and ‘Second Voice’ ( 1995: 4 ) . The two voices use similes repeatedly in order to compare one thing to another. An illustration of a simile within the drama is when Mrs Cherry Owen defines Mr Cherry Owen as being ‘as rummy as a deacon’ ( 1995: 26 ) . The consequence of this simile is that it highlights the inebriation of Mr Cherry Owen and draws the audience in because the audience would be shocked at the innuendo of a deacon being rummy.Under Milk Woodbesides contains many metaphorical statements. For illustration ; ‘the small pink eyed cottage’ ( 1995: 8 ) . This metaphor gives the bungalow life qualities and personifies it leting the audience to care and link to the object despite it being inanimate. Alliteration is besides often used in order to add accent and deepness to Thomas’s descriptions of the small town and its milieus. For illustration ; the first voice speaks about Bessie Bighead being asleep, and the voice says ‘sleep until the dark sucks out her psyche and spits it into the sky’ ( 1995: 55 ) . Here, Thomas is utilizing alliterative and onomatopoetic sounds for the old lady in order to pull attending to the line. A farther poetic technique which Thomas uses is strong images which are built up utilizing different semantic Fieldss in order to make images in the head of the audience. An illustration of this is when the first voice says: ‘Now, in her ice-berg white, holily laundered, crinoline night-gown, under virtuous polar sheets, in her spruced and scoured dust-defying sleeping room in trig and spare Bay view’ ( 1995: 12 ) . The consequence of this image is to demo us how clean Mrs Ogmore Prichard’s house is with the usage of statements such as ‘ice-berg white’ and ‘dust-defying bedroom’ . Although Thomas could hold merely said that the house was really clean, he chose to give the audience an image in their heads to assistance with clearly visualizing the scene. A farther illustration is ‘the sloeblack, decelerate, black, crowblack, fishingboat-bobbing sea’ ( 1995: 3 ) . The usage of such complex images and poetic linguistic communica tion which is used by the first and 2nd storytellers gives effectual contrast to that of the ordinary, mundane linguistic communication of the citizens of Llareggub. The inclusion of poetic techniques in a piece that is meant to be dramatic creates centripetal feelings for the audience to go immersed in. They besides give Llareggub a dreamlike and charming feeling which leaves the reader with a feeling of admiration and child-like phantasy. Thomas does non merely convey ocular images through descriptive linguistic communication, but he allows the audience to see the town by listening to the sounds which the storytellers are invariably directing us towards. The first and 2nd voices often invite the audience to ‘listen’ as ‘only you can hear’ ( 1995: 4 ) . There are no sound effects in the drama ; hence, sounds must be created by the descriptions which Thomas gives to us. For illustration: ‘the sea interruption and the chitchat of birds’ ( 1995: 20 ) , ‘shrill misss giggle ( 1995: 45 ) and ‘the clippety-clop of Equus caballuss†¦ ..pigs are grunting, chop goes the meatman, milk-churns bell, boulder claies ring, sheep cough, Canis familiariss shout, saws sing’ ( 1995: 34 ) . Again the consequence of this is to let the audience to visualize the town utilizing sound as an concomitant to the ocular images which he invariably feeds. Thomas uses the Welsh poetic cons truct of ‘cynghanedd’ ( 2009 ) throughoutUnder Milk Woodwhich is the internal sound agreement utilizing beat, riming, vowel rhyme and speech pattern. The usage of this device creates velocity and energy which drives the twenty-four hours into dark once more. A good illustration of this is ‘There’s the, cartridge holder clunking or Equus caballuss on the sunhoneyed setts of the humming streets, hammering of horse-shoes, gobble quack and cackle, tomtit chirrup from the bird-ounced boughs’ ( 1995: 34 ) . ‘The voice of a Guide-book’ ( 1995: 19 ) storyteller is intended to give comparing to the first and 2nd voice storytellers. The usher is impersonal and distant in comparing to the two voices ; it does non look to cognize the town really good and does non talk to the audience in the same mode as the first two voices do. It abuses the town and the occupants whilst looking down upon their manner of life and doing the town seem drilling and uneventful. For illustration: the guide-book voice describes the little houses as ‘prinking themselves out in petroleum colorss and the broad usage of pink wash’ ( 1995: 19 ) and describes the town as ‘this little disintegrating watering-place’ ( 1994: 19 ) . The Guide-book is highly negative with respects to Llareggub, and uses cliches such as ‘cobbled streets and its small fishing habour’ ( 1995: 19 ) to do the topographic point appear worn out and antique. Thomas’s usage of neologies are outstanding throughout the drama and are largely in the signifier of compound nouns and participle adjectives such as ‘fishingboat-bobbing sea’ ( 1995: 3 ) and ‘jellyfish-slippery’ ( 1995: 4 ) . The usage of these is to enable Thomas to maintain the beat in flow with the remainder of the text and give ‘interesting ideological effects’ ( 2010: 18 ) which paradox human linguistic communication. Page 9 through to page 12 sees Thomas use an ancient Hellenic technique called stichomythia ( 1975: 143-176 ) . This is a technique which was besides famously used by Shakespeare throughout his work ( 2009 ) and comprises of two or more characters prosecuting in quick-fire address. This is besides repeated on page 28 and pages 35-36. This speedy exchange of address gives the audience a sense of velocity and picks up the gait until the conversation is over. There is a noticeable sum of innuendo nowadays inUnder Milk Woodalong with dual entendre and boylike temper. For illustration: on page 60, Mr Waldo says ; ‘nobody’s swept my chimbley/Since my hubby went his ways/Come and brush my chimbley/Bring along your chimbley brush’ ( 1995: 60 ) and ‘Lie down, lie easy. Let me shipwreck in your thighs’ ( 1995: 52 ) . Despite the boylike insinuation, there are illustrations of descriptive and mildly titillating lines. An illustration of this is ‘The Sun hums down through the cotton flowers of her frock into the bell of her bosom and bombilation in the honey at that place and sofas and busss, lazy-loving and boozed, in her red-berried breast’ ( 1995: 46 ) . The consequence this has upon the text is one of temper and visible radiation –hearted screening of the characters making a threading bond between the audience and the citizens of Llareggub. The inclusion and intermingling of all these techniques has allowed Thomas to make an improbably sensuous piece of literary art which flows swimmingly with the carefully crafted rhythmic linguistic communication and crisp pacing. Richard Burton considers Under Milk Wood to be ‘a amusing masterpiece’ ( Rees: 2014 ) , one that will populate everlastingly in the immortal voices of his far-out characters. Word Count: 2230 ( excepting bibliography ) Bibliography.Biography of Dylan Thomas.( 2014 ) hypertext transfer protocol: //www.poemhunter.com/dylan-thomas/biography/ Accessed ( 01/04/2014 )Drabble, M. ( 2009 )The Oxford Companion to English Literature.Oxford: Oxford University Press.Jeffries, L. ( 2010 ) . Critical Stylistics: The Power of English. Basingstoke: Macmillan.Jeffries, L. & A ; McIntyre, D. ( 2011 ) Teaching Stylistics. London: MacmillanO’Toole ( 1975 )Analytic and Man-made Approaches to Narrative Structurein Style and Structure in Literature. United kingdom: Blackwell.Thomas, D. ( 1954 )Under Milk Wood. ( The Definitive edition – 1995. ) London: Everyman.Thomas, D. ( 1958 )Return Journey Home. Hammersmith: Lyric Theatre.Thomas, D. ( 1946 )Death and Entrances.United kingdom: Jackdaw Books.Turner, W. J. ( 1946 ) . The Spectator. Pg. 176. The Spectator.West, J. ( 2009 ) .Welsh Poetry – Part I: Cynghaneddhypertext transfer protocol: //allpoetry.com/column/7546199-Welsh-Poetry — -Part-I-Cyng hanedd — by-Welshbard ( accessed 30/03/2014 )Rees, J. ( 2014 )Why Under Milk Wood is the greatest wireless drama of all time.The Telegraph.